Make sure that the channel you select is the same channel your access point or the other card in an ad-hoc network is on. In order to do this, use ” mediaopt hostap ” to ifconfig The interface should behave more or less like an ethernet interface. A number of useful tools for IEEE The number of available channels depends on your country,
|Date Added:||11 August 2009|
|File Size:||31.96 Mb|
|Operating Systems:||Windows NT/2000/XP/2003/2003/7/8/10 MacOS 10/X|
|Price:||Free* [*Free Regsitration Required]|
To use them, add one of the following to your kernel config:. Once you’ve booted a kernel with a Remember, these values are probably not right for you!!
This is probably obvious to some, but if you don’t see the PCMCIA card, the problem probably lies with the configuration of the pcic device. In one case, the following configuration was used:. The ‘resources’ tab of each device in the “Device Manager”.
Assuming you haven’t changed anything yet, use ifconfig 8 and wiconfig 8 to show the card’s current configuration. To find the correct value for your system, you need to luecnt consult documentation if you can find itor write down every single range used by every single device under Windows, and pick a range that appears empty.
Lucent WaveLAN/IEEE Bronze
To use them, add one of the following to your kernel config: On certain machines the wi will appear to work until traffic is actually sent, at which point it will lock the entire machine.
The number of available channels depends on your country, In one case this range may not wavelan/ieer for you! Skip to main content. A number of useful tools for IEEE You may also want to set different media and media options according to the output of ” ifconfig -m “, e. Sometimes you may get a ping response, sometimes not, but invariably waveelan/ieee will lock up. If in doubt, please refer to the documentation that came with your card or access point.
Lucent WaveLAN/IEEE Bronze – WikiDevi
You’ll see ping times go up, but your power consumption should decrease. In order to do this, use ” mediaopt hostap ” to ifconfig In order to do this, use ” mediaopt hostap ” to ifconfig 8: Windows gave the answer as it was using 0xcc and the card working. Tran’s web page on how to build a wireless This document describes how to configure and troubleshoot IEEE It requires a Macintosh running Mac OS 8.
Once you have good communication with the base station or other ad-hoc device, you should configure the wireless network interface just like you would any other network interface. WEP encryption can be enabled using ” ifconfig nwkey ” with a number of options, see ifconfig 8 for more information.
Assuming you have APM configured correctly, you should see the card go into power-saving mode when you disconnect the mains, and return to normal usage when it’s plugged back in!
If you need to change this, use the ifconfig 8 “ssid” keyword or “nwid”, if you are on NetBSD 1. The interface should behave more or less like an ethernet interface. Power-saving can be enabled with ” ifconfig ath0 powersave “, use ” ifconfig ath0 -powersave ” to disable it ,ucent.
This is a common problem with laptops; documentation is somewhat sparse, and NetBSD isn’t very good yet at all forms of autodetection. Assuming that the defaults are correct for your network, you should see “Current netname” or SSID wavelan/iieee to reflect the name of the wireless network which has been set in the access point your card is communicating with.
In particular, you may need to tweak the iomem and possibly lucenf parameters of the pcic 4 device. These values may not work for you!
To determine if your network connection between your wireless card and a base station is enabled, check ifconfig 8 output, status should be “active” there. If there is no change, you may need to adjust the channel your card is communicating on, using ” ifconfig ath0 chan XX ” for channel XX. The default for cards sold in North America and most of Europe is 3; the default for cards sold in France is 11, and the default for cards sold in Japan is